DHOUS Dock House. Standard Series

Loading dock house is a modular unit with an installed dock leveler and a shelter. Loading dock houses are bolted to a building’s exterior to preserve microclimate, save interior floor space, and seal out unwanted contaminants. These units are ideal for temperature-controlled warehouses and distribution centres where the entire building space is used or trailers can’t be parked perpendicular to the building.
DHOUS Dock House. Standard Series

Application

Warehouses and logistics centres

Advantages

1
2

Design

RAL 7038 Agate grey
RAL 7038 Agate grey
RAL 9003 Signal white
RAL 9003 Signal white
RAL 5005 Signal blue
RAL 5005 Signal blue
RAL 7004 Signal grey
RAL 7004 Signal grey
RAL 3000 Flame red
RAL 3000 Flame red

Construct and sizes

Construction
  • 1. Wall
  • 2. Supports
  • 3. Roof
  • 4. Frame
Parameters Value
Width, mm 2 800–3 600
Height, mm 3 700–6 600
Length, mm 2 030–7 648

Mounting

Mounting on steel embedded plates. This is a preferable type of installation including embedment of steel plates (400 х 400 mm) in particular places of a concrete base during preparation of installation site for a dock house. Mounting on concrete base (with anchor bolts). This type of installation is used when steel plates were not embedded during concrete base pouring. Mounting on steel embedded plates. This is a preferable type of installation including embedment of steel plates (400 х 400 mm) in particular places of a concrete base during preparation of installation site for a dock house. Mounting on concrete base (with anchor bolts). This type of installation is used when steel plates were not embedded during concrete base pouring.
Mounting on walls of different types (concrete, brick, metal, wooden, sandwich panels of 50 to 200 mm thickness). Mounting on walls of different types (concrete, brick, metal, wooden, sandwich panels of 50 to 200 mm thickness).
DHOUS 90 series. Standard straight dock house (90°) for an embedded type dock leveler with hinged or telescopic lip. DHOUS 90 series. Standard straight dock house (90°) for an embedded type dock leveler with hinged or telescopic lip.
Symbol, parameter name Calculation formula
Hd, mm Shelter width 2 800–3 600
Bd, mm Shelter height 2 800–4 900
Hf, mm Ramp height 900–1 400 (1 200 as standard)
Lh, mm Leveler length (overall) any
Bh, mm Leveler width (overall) any
Hh, mm Leveler height any
A°, Angle 90
DHOUS 60 series. Standard angled dock house (60°) for an embedded type dock leveler with hinged or telescopic lip. DHOUS 60 series. Standard angled dock house (60°) for an embedded type dock leveler with hinged or telescopic lip.
Symbol, parameter name Calculation formula
Hd, mm Shelter width 2 800–3 600
Bd, mm Shelter height 2 800–4 900
Hf, mm Ramp height 900–1 400 (1 200 as standard)
Lh, mm Leveler length (overall) any
Bh, mm Leveler width (overall) any
Hh, mm Leveler height fny
A°, Angle 60; turned to the right or to the left (view from the building)
DHOUS 45 series. Standard angled dock house (45°) for an embedded type dock leveler with hinged or telescopic lip. DHOUS 45 series. Standard angled dock house (45°) for an embedded type dock leveler with hinged or telescopic lip.
Symbol, parameter name Calculation formula
Hd, mm Shelter width 2 800–3 600
Bd, mm Shelter height 2 800–4 900
Hf, mm Ramp height 900–1 400 (1 200 as standard)
Lh, mm Leveler length (overall) any
Bh, mm Leveler width (overall) any
Hh, mm Leveler height any
A°, Angle 45; turned to the right or to the left (view from the building)
DHOUS 30 series. Standard angled dock house (30°) for an embedded type dock leveler with hinged or telescopic lip. DHOUS 30 series. Standard angled dock house (30°) for an embedded type dock leveler with hinged or telescopic lip.
Symbol, parameter name Calculation formula
Hd, mm Shelter width 2 800–3 600
Bd, mm Shelter height 2 800–4 900
Hf, mm Ramp height 900–1 400 (1 200 as standard)
Lh, mm Leveler length (overall) any
Bh, mm Leveler width (overall) any
Hh, mm Leveler height any
A°, Angle 30; turned to the right or to the left (view from the building)

Complectations

Walls — sandwich panel (interior/exterior colour – RAL 9003); roof — С44 profiled sheeting (zinc-plated)
Walls — sandwich panel (interior/exterior colour – RAL 9003); roof — С44 profiled sheeting (zinc-plated)
Steel plate used when building plinth is 0 mm (building plinth is flush with building wall)
Steel plate used when building plinth is 0 mm (building plinth is flush with building wall)
Pre-drilled holes for installation of any chosen bumper
Pre-drilled holes for installation of any chosen bumper
Without roof and walls
Without roof and walls
Steel angle used when building plinth is 1—500 mm (building plinth projects for 1–500 mm)
Steel angle used when building plinth is 1—500 mm (building plinth projects for 1–500 mm)
Insulation of the roof with sandwich panels
Insulation of the roof with sandwich panels
Walls — С20 profiled sheeting. 4 standard colours: RAL 9003 (signal white), RAL 5005 (signal blue), RAL 7004 (signal grey), RAL 3000 (flame red)
Walls — С20 profiled sheeting. 4 standard colours: RAL 9003 (signal white), RAL 5005 (signal blue), RAL 7004 (signal grey), RAL 3000 (flame red)
Walls — any profiled sheeting. Colour according customer’s request
Walls — any profiled sheeting. Colour according customer’s request
Flashings used to cover the junction between a dock house and a warehouse wall
Flashings used to cover the junction between a dock house and a warehouse wall
Molded rubber bumpers 250х250х100 mm. Standard. Product number BR250x250x100. Ensure safe truck reversing into the loading dock, protect the building walls. For mounting dimensions, please, refer to drawings
Molded rubber bumpers 250х250х100 mm. Standard. Product number BR250x250x100. Ensure safe truck reversing into the loading dock, protect the building walls. For mounting dimensions, please, refer to drawings
Molded rubber bumpers 450x250x100 mm. Standard. Product number BR450x250x100. Ensure safe truck reversing into the loading dock, protect the building walls. For mounting dimensions, please, refer to drawings
Molded rubber bumpers 450x250x100 mm. Standard. Product number BR450x250x100. Ensure safe truck reversing into the loading dock, protect the building walls. For mounting dimensions, please, refer to drawings
Molded rubber bumpers 510х250х330 mm (external dimensions), console type. Based on rubber bumper 450x250x100 mm. Product number BRC510х250х330. Ensure safe truck reversing into the loading dock, protect the building walls. Used when truck load bed is higher than the ramp. For mounting dimensions, please, refer to drawings
Molded rubber bumpers 510х250х330 mm (external dimensions), console type. Based on rubber bumper 450x250x100 mm. Product number BRC510х250х330. Ensure safe truck reversing into the loading dock, protect the building walls. Used when truck load bed is higher than the ramp. For mounting dimensions, please, refer to drawings
Molded rubber bumpers 610х250х175. (external dimensions), moving. Based on rubber bumper 450x250x100 mm. Product number BRM610х250х175. Move up and down following vehicle raising and lowering as the suspension floats during the loading/unloading cycle. Has greater service life. For mounting dimensions, please, refer to drawings
Molded rubber bumpers 610х250х175. (external dimensions), moving. Based on rubber bumper 450x250x100 mm. Product number BRM610х250х175. Move up and down following vehicle raising and lowering as the suspension floats during the loading/unloading cycle. Has greater service life. For mounting dimensions, please, refer to drawings
Molded rubber bumpers 600х364х110 mm (external dimensions), adjustable. Based on rubber bumper 450x250x100 mm. Product number BRM600х364х110. Move up and down following vehicle raising and lowering as the suspension floats during the loading/unloading cycle. Has greater service life. Can be used only with dock levelers with 1 000 mm telescopic lip. For mounting dimensions, please, refer to drawings
Molded rubber bumpers 600х364х110 mm (external dimensions), adjustable. Based on rubber bumper 450x250x100 mm. Product number BRM600х364х110. Move up and down following vehicle raising and lowering as the suspension floats during the loading/unloading cycle. Has greater service life. Can be used only with dock levelers with 1 000 mm telescopic lip. For mounting dimensions, please, refer to drawings
Steel face dock bumpers 465х250х165 mm (external dimensions) with 16 mm steel plate. Based on rubber bumper 450x250x100 mm. Product number BRSP(16)465х250х165. Consist of a rubber bumper 450x250x100 mm covered with durable steel plate. Steel face improves life expectancy of the rubber bumper and protects it from damaging by parking vehicle and during loading/unloading cycle. Manufacturer’s warranty doesn’t cover steel plate replacement in case of wear and deformation due to its extreme abnormal wear. For mounting dimensions, please, refer to drawings
Steel face dock bumpers 465х250х165 mm (external dimensions) with 16 mm steel plate. Based on rubber bumper 450x250x100 mm. Product number BRSP(16)465х250х165. Consist of a rubber bumper 450x250x100 mm covered with durable steel plate. Steel face improves life expectancy of the rubber bumper and protects it from damaging by parking vehicle and during loading/unloading cycle. Manufacturer’s warranty doesn’t cover steel plate replacement in case of wear and deformation due to its extreme abnormal wear. For mounting dimensions, please, refer to drawings
Steel face dock bumpers 465х250х165 mm (external dimensions) with 16 mm steel plate and parking sensor. Based on rubber bumper 450x250x100 mm. Product number BRSP(16)465х250х165S. Consists of a rubber bumper 450x250x100 mm covered with durable steel plate and parking sensor. Steel face improves life expectancy of the rubber bumper and protects it from damaging by parking vehicle and during loading/unloading cycle. Manufacturer’s warranty doesn’t cover steel plate replacement in case of wear and deformation due to its extreme abnormal wear. This dock bumper is used together with parking radar. For mounting dimensions, please, refer to drawings
Steel face dock bumpers 465х250х165 mm (external dimensions) with 16 mm steel plate and parking sensor. Based on rubber bumper 450x250x100 mm. Product number BRSP(16)465х250х165S. Consists of a rubber bumper 450x250x100 mm covered with durable steel plate and parking sensor. Steel face improves life expectancy of the rubber bumper and protects it from damaging by parking vehicle and during loading/unloading cycle. Manufacturer’s warranty doesn’t cover steel plate replacement in case of wear and deformation due to its extreme abnormal wear. This dock bumper is used together with parking radar. For mounting dimensions, please, refer to drawings
Steel face dock bumpers 500х255х205 (external dimensions) with damper insert. Based on rubber bumper 450x250x100 mm. Product number BS500х255х205. It’s a hybrid device combining moving bumper and steel plate bumper. Consists of a holder, a rubber crumb damper insert and a moving steel plate following truck bed movement. Steel face improves life expectancy of the rubber bumper and protects it from damaging by parking vehicle and during loading/unloading cycle. Manufacturer’s warranty doesn’t cover steel plate replacement in case of wear and deformation due to its extreme abnormal wear. Can be used only with dock leveler with 1 000 mm telescopic lip For mounting dimensions, please, refer to drawings
Steel face dock bumpers 500х255х205 (external dimensions) with damper insert. Based on rubber bumper 450x250x100 mm. Product number BS500х255х205. It’s a hybrid device combining moving bumper and steel plate bumper. Consists of a holder, a rubber crumb damper insert and a moving steel plate following truck bed movement. Steel face improves life expectancy of the rubber bumper and protects it from damaging by parking vehicle and during loading/unloading cycle. Manufacturer’s warranty doesn’t cover steel plate replacement in case of wear and deformation due to its extreme abnormal wear. Can be used only with dock leveler with 1 000 mm telescopic lip For mounting dimensions, please, refer to drawings
Steel face dock bumper 800х255х205 (external dimensions) with damper insert. Based on rubber bumper 450x250x100 mm. Product number BS800х255х205. It’s a hybrid device combining moving bumper and steel plate bumper. Consists of a holder, a rubber crumb damper insert and a moving steel plate following truck bed movement. Steel face improves life expectancy of the rubber bumper and protects it from damaging by parking vehicle and during loading/unloading cycle. Manufacturer’s warranty doesn’t cover steel plate replacement in case of wear and deformation due to its extreme abnormal wear. Can be used only with dock leveler with 1 000 mm telescopic lip For mounting dimensions, please, refer to drawings
Steel face dock bumper 800х255х205 (external dimensions) with damper insert. Based on rubber bumper 450x250x100 mm. Product number BS800х255х205. It’s a hybrid device combining moving bumper and steel plate bumper. Consists of a holder, a rubber crumb damper insert and a moving steel plate following truck bed movement. Steel face improves life expectancy of the rubber bumper and protects it from damaging by parking vehicle and during loading/unloading cycle. Manufacturer’s warranty doesn’t cover steel plate replacement in case of wear and deformation due to its extreme abnormal wear. Can be used only with dock leveler with 1 000 mm telescopic lip For mounting dimensions, please, refer to drawings
LED dock light
LED dock light

Extra information

  • Carry out technical inspection and maintenance of the dock house regularly to provide its safe and smooth operation.
  • In winter remove excess snow buildup from on top of the house, shelter and leveler. Clean the surrounding territory of the warehouse to ensure correct positioning of trailers.
  • Speed of a parking trailer should be minimum, not more than 1 km/h (30 sm/sec).
  • Do not drive over the house frame with forklifts and other lifting equipment. Drive only on the leveler deck and house triangle.
  • Attention! Check bumpers for signs of wear and tear regularly. Should bumper residual thickness comprise less than 50 mm or there is no bumper material at all stop using the dock house until new bumper material is installed.
Packing in cardboard Packaging features
Length, mm base (depends on leveler length) — 2 000–4 500; legs — 2 800–3 600; triangle — 2 800–3 600; frame — 6 536 (max); flashing — 2 500; walls — 5 962 (max); roof — 7 788 (max)
Width, mm base — 785 (max); legs — 300; triangles — 3 400; frame — 500 (max); flashing — 200; walls — 2 400 (max); roof — 1 100
Height, mm base — 800 (max); legs — 550 (max); triangles — 200; frame — 500 (max); flashing — 200; walls — 50; roof — 150 (max)
Contents base, legs, triangles, frame, flashing, walls, roof, a box with hardware
Contents sandwich panel walls of the dock house are supplied disassembled. They are assembled during installation of the dock house
DoorHan warrants the dock house to operate properly for a period of 1 year from purchase date for retail orders and for 2 years from purchase date for dealer orders.
  • All the DoorHan products are loaded with hydraulic crane or fork-lift truck with 2 m long forks. Customer or installer is recommended to use similar equipment. When lifting with crane or other lifting device use slings of corresponding lifting capacity.

Other customers also looked at

Navigation