RSD02-SLP Single-Skin Panel Door with Torsion Spring Mechanism

RSD02-SLP single-skin panel doors are designed for small-sized door openings. They coordinate perfectly with premises which don’t need any heat insulation such as covered parkings, unheated garages, etc. RSD02-SLP doors can be installed in openings of 2 000–3 500 mm width and 1 800–3 000 mm height with headroom clearance of 210 mm and side room clearance of 120 mm.
RSD02-SLP Single-Skin Panel Door with Torsion Spring Mechanism

Application

Premises which don’t need heat insulation (garages, service rooms)
Covered parking, garages

Advantages

1
2

Design

S-line
S-line
Stucco — outside
Stucco — outside
Stucco — inside
Stucco — inside
Outside surface colour — RAL 9003 (white)
Outside surface colour — RAL 9003 (white)
Inside surface colour — grey
Inside surface colour — grey

Construct and sizes

Construction
  • 1. Torsion spring mechanism
  • 2. U-shaped end support bracket
  • 3. Horizontal track
  • 4. Side support bracket with rollers
  • 5. Vertical angle
  • 6. Side cap
  • 7. Mounting bracket for vertical tracks
  • 8. Mounting bracket for angles
  • 9. Universal mounting bracket for horizontal tracks
  • 10. Top support bracket
  • 11. Panel reinforcement
  • 12. Single-skin panels
  • 13. Bottom corner bracket
  • 14. Bottom profile and sealer
  • 15. Handle
  • 16. Hinge
Parameters Value
Opening height, mm from 1 800 to 3 000
Opening width, mm from 2 000 to 3 500
Headroom, mm from 210 mm for low lift
Headroom, mm from 320 mm for standard lift
Sideroom clearance, mm from 120 mm
Opening Dimensions

Mounting

Checking Dimensional Details
  • All the necessary measurements are taken inside the premises with just a measuring tape and a water level. Every dimension should be taken at least in three points:
  • H — opening height (distance from floor to opening top);
  • B — opening width (distance between left and right side of the opening);
  • h — headroom (distance between opening top and ceiling) min 210 mm;
  • b1/ b2 — left/right side room (distance between a corresponding opening edge and obstacle) min 120 mm;
  • L — backroom.
  • When measuring Н and В the largest figure is taken for final dimension.
  • When measuring h, b1, b2 and L the smallest figure is taken for final dimension.

Difference of floor level along the opening should not exceed 10 mm. Make sure that mounting surface of headroom and side rooms is level. The inside perimeter of the door opening should be framed with metal or other solid material in case the surface is not concrete or solid enough to install tracks system.

Overhead mounting. All the tracks are mounted on the inner side of headroom and side rooms. Overhead mounting. All the tracks are mounted on the inner side of headroom and side rooms.
Low lift, front mount Low lift, front mount
Symbol, parameter name Calculation formula
H, mm Opening height H
h, mm Headroom height h ≥ 210
B, mm Opening width B
A, mm Angle track height H + 54
Ab, mm Height of shaft axle and drum A + 59
A1, mm Vertical track height А - 543
A2, mm Horizontal track height А - 106
E, mm Horizontal track length Н + 315
S, mm Minimum side room clearance 120
P, mm Door opener position Н + 1 185
n, mm Opening overlapping 245 (without door operator); 40...60 (with door operator)
Standard lift Standard lift
Symbol, parameter name Calculation formula
H, mm Opening height H
h, mm Headroom height h ≥ 320
B, mm Opening width B
A, mm Angle track height H + 165
Ab, mm Height of shaft axle and drum A + 59
A1, mm Vertical track height A — 490
A2, mm Horizontal track height А - 53
E, mm Horizontal track length H + 250
Db, mm Torsion spring operation space 100
S, mm Minimum side room clearance 120
P, mm Door opener position Н + 1 060

Complectations

Door leaf of 40 mm single–skin panels with reinforcements.
Door leaf of 40 mm single–skin panels with reinforcements.
Side tracks have simple construction and all the necessary perforation.
Side tracks have simple construction and all the necessary perforation.
High-quality durable torsion springs designed for 25 000 operating cycles provide effortless closing and opening of the door.
High-quality durable torsion springs designed for 25 000 operating cycles provide effortless closing and opening of the door.
A set of hardware, instruction manual and product technical data.
A set of hardware, instruction manual and product technical data.
Spring-break safety device blocks the shaft preventing door panel from falling.
Spring-break safety device blocks the shaft preventing door panel from falling.
T-lock blocks the door leaf both from inside and outside the premise.
T-lock blocks the door leaf both from inside and outside the premise.
Latch lock blocks the door leaf from inside the premise. Simple and reliable.
Latch lock blocks the door leaf from inside the premise. Simple and reliable.

Extra information

  • Door leaf should smoothly slide vertically along the tracks, and be properly balanced, i. e. torsion springs should compensate leaf weight.
  • Use door handle to open/close your sectional door manually.
  • Do not lift too much force when opening/closing the door. Prevent any sharp movements of the door.
  • Keep people and animals clear of opening while door is operated.
  • Never stay or cross an opening under a moving door leaf as it may cause serious injury or death.
  • Don’t strike the door leaf or obstruct its movement.
  • Keep tracks and rollers clean, as dirt may prevent smooth movement of the door and cause overloading and damage of a door operator (if used).
  • Keep the door opening clear of any objects and litter as it may unbalance and jam the door leaf.
Packing in cardboard Packaging features
Contents the door leaf and the tracks system are packed in a fibre board and polystyrene combination wrapped in a stretch film. Hardware is packed in a box wrapped in a stretch film. All packages are labeled with stickers containing order information and DoorHan logo
Contents corrugated fiberboard, polystyrene, stretch-film, adhesive tape
Width, mm from 500 to 800
Height, mm from 200 to 400
Length, mm from 2 100 to 3 600
Gross weight, kg up to 100
Number of items in the packaging leaf package — from 4 to 5 panels; tracks package — 1 track system; mounting items — 1 box
DoorHan warrants to the original purchaser of the product that the sandwich panels and steel profiles of the track system will be free from corrosion for a period of ten years.
  • Sandwich panels should be stored in producer’s packaging on a flat horizontal surface in warehouses or under a canopy for a period not exceeding 6 months from the production date. Provide proper protection from water, snow, dirt, and direct sunlight.

Other customers also looked at

Navigation