Counter Shutters of RHS52 Steel Profile

DoorHan offers roller shutters corresponding to International and European quality and safety standards, suitable for operation in different climatic conditions. Roller shutters and roll-up doors are used to protect door and window openings from burglary and adverse weather conditions. All the roller shutter components are produced on modern automated lines with the use of equipment from leading manufacturers. All metal parts are zinc-coated or painted to ensure corrosion resistance, prevent negative effects of aggressive environments, and prolong operational life of roller shutters. Reliability of roller shutters, safety of their operation and compliance with International standards are confirmed by corresponding certificates.
Counter Shutters of RHS52 Steel Profile

Application

Window and door openings

Advantages

1
2

Design

RHS52 steel profile
RHS52 steel profile
White
White
Brown
Brown
Not-painted (zinc-coated)
Not-painted (zinc-coated)

Construct and sizes

Construction
  • 1. Hood side cap RK165, RK180, RK205, RK250, RSK300
  • 2. Bearing support BS100, BS42
  • 3. Entry guide device RU65
  • 3a. Guiding roller RU77
  • 4. Bearing BR28, BR42
  • 5. Universal capsule KP60, KPU60, KPU70, KPU70S, KPU102
  • 6. Octagonal shaft RV60, RV70, RV102
  • 7. Security lock ring RD60, RD70
  • 8. Hood RBN165, RBN180, RBN205, RBN250, RBN300
  • 9. Security spring RS160
  • 10. Tubular motor
  • 11. Headplate BU100K
  • 12. Guide rail RG65BS, RG70BS
  • 13. Plug PB14
  • 14. End lockSL52
  • 15. End profile RA50EM
  • 16. Slat (curtain) RHS52
  • 17. Key lock switch SWM, SWK
  • 18. Key switch SWB, SWH
Parameters Value
Opening height, mm from 500 to 5 000
Opening width, mm from 600 to 4 000
Maximum door curtain area, sqm 14
Headroom, mm from 165 (face to wall installation)
Sideroom clearance, mm from 65 (face to wall installation)
Opening Dimensions

Mounting

Checking Dimensional Details
  • Opening parameters for overhead mounting: H — opening height (max), mm B — opening width (max), mm h1 — headroom (min), mm b1 and b2 — sideroom clearance (min), mm Use a measuring tape and a water level, or electronic measuring instruments to take all the necessary measurements. Every dimension should be taken at least in three points. When measuring the opening for overhead mounting take into account walls unevenness and reduce the measuring 5-10 mm.

Observe the following requirements when preparing the opening: the opening must be perpendicular, plumb, and square; it should have smooth and level surfaces having no build-ups of plaster and cracks; the walls should be monolith, without cavities (concrete, metal, solid brick); in case of installation on hollow brick wall edge the opening with metal angle; interior and exterior walls in place of the shutter mounting should be flat, without bulges and hollows; deviations of working surfaces from vertical and horizontal should not exceed 1,5-5 mm per meter and the difference of the diagonals — not more than 5 mm.

Face of wall mount. The most popular type of installation which doesn’t require time-consuming preparation of the slopes and niche for the shutter box. Shutter box with curtain is installed above the opening while the guide rails — on either side of the opening. Face of wall mount. The most popular type of installation which doesn’t require time-consuming preparation of the slopes and niche for the shutter box. Shutter box with curtain is installed above the opening while the guide rails — on either side of the opening.
Between jambs mount, shutter box outward. All the rolling shutter components are installed inside the door or window opening. The window or door itself should open inward the premises. Between jambs mount, shutter box outward. All the rolling shutter components are installed inside the door or window opening. The window or door itself should open inward the premises.
Between jambs mount, shutter box inward. The roller shutter is installed inside the opening with the shutter box turned inward so that the curtain is flush with the opening outside surface. Between jambs mount, shutter box inward. The roller shutter is installed inside the opening with the shutter box turned inward so that the curtain is flush with the opening outside surface.
Rolling shutters operated with strap, rope or cord crank Easy to operate strap crank is used with light weight shutters weighing less than 15 kg. Shutter curtain is raised and lowered by the strap tension. Rope crank operates shutters weighing less than 20 kg. Turning the handle of the rope winder operates shutter curtain. Cord crank raises rolling shutters weighing up to 40 kg with strong steel cord. The principle of operation is similar to the rope crank. Rolling shutters operated with strap, rope or cord crank Easy to operate strap crank is used with light weight shutters weighing less than 15 kg. Shutter curtain is raised and lowered by the strap tension. Rope crank operates shutters weighing less than 20 kg. Turning the handle of the rope winder operates shutter curtain. Cord crank raises rolling shutters weighing up to 40 kg with strong steel cord. The principle of operation is similar to the rope crank.
Rolling shutters operated with rod crank.  Rod crank can raise shutters weighing up to 30 kg. Turning the crank rod clockwise you raise the curtain, turning it counterclockwise you lower the curtain. Rolling shutters operated with rod crank. Rod crank can raise shutters weighing up to 30 kg. Turning the crank rod clockwise you raise the curtain, turning it counterclockwise you lower the curtain.
Rolling shutters with spring loaded mechanism. Spring loaded mechanism is used to operate shutters weighing up to 60 kg. Rolling shutters are easily raised manually and lowered quickly under their own weight thanks to a torsion spring balancing the shutter curtain and installed on the octagonal shaft. Rolling shutters with spring loaded mechanism. Spring loaded mechanism is used to operate shutters weighing up to 60 kg. Rolling shutters are easily raised manually and lowered quickly under their own weight thanks to a torsion spring balancing the shutter curtain and installed on the octagonal shaft.

Complectations

Hood assembly. The set comprises of a hood, side caps, shaft, capsules and operating mechanism – manual or automatic.
Hood assembly. The set comprises of a hood, side caps, shaft, capsules and operating mechanism – manual or automatic.
Curtain assembly. Assembly of steel profiles with side locks, preventing slats from disengaging.
Curtain assembly. Assembly of steel profiles with side locks, preventing slats from disengaging.
End profile with seal. End profile can be fitted with a locking mechanism.
End profile with seal. End profile can be fitted with a locking mechanism.
Guide rails with seals. Wide variety of standard and reinforced guide rails allows rolling shutters to be installed in openings of any size taking into account wind load and complying with burglary resistance requirements.
Guide rails with seals. Wide variety of standard and reinforced guide rails allows rolling shutters to be installed in openings of any size taking into account wind load and complying with burglary resistance requirements.
Manual or automatic drive.
Manual or automatic drive.
Box for the components.
Box for the components.
SWB key-switch for face of wall installation
SWB key-switch for face of wall installation
SWM key-button switch (metal). Turning the key of SWM switch transmits a controlling signal to the control box of the electric drive shaft
SWM key-button switch (metal). Turning the key of SWM switch transmits a controlling signal to the control box of the electric drive shaft
CV01 control box for remote control of one or several rolling shutters
CV01 control box for remote control of one or several rolling shutters
SmartRoll control box for remote control of tubular motors with DoorHan remote transmitters
SmartRoll control box for remote control of tubular motors with DoorHan remote transmitters
Roll1/2 control box for remote control of tubular motors with DoorHan remote transmitters
Roll1/2 control box for remote control of tubular motors with DoorHan remote transmitters
GC2/GC4 control boxes for several shutters control. GC2 box controls two motors with one switch; GC4 box — controls four motors
GC2/GC4 control boxes for several shutters control. GC2 box controls two motors with one switch; GC4 box — controls four motors
External DHRE-1 receiver controls other manufactures’ automatic devices with DoorHan remote control
External DHRE-1 receiver controls other manufactures’ automatic devices with DoorHan remote control
Wi-Fi-module for wireless control of electric drives (control signal, NO)
Wi-Fi-module for wireless control of electric drives (control signal, NO)
GSM-module receives a mobile phone signal and transmits a control signal to operate electric drive
GSM-module receives a mobile phone signal and transmits a control signal to operate electric drive
T5 remote transmitter can operate five roller shutters
T5 remote transmitter can operate five roller shutters
Transmitter-4 remote control operates four devices
Transmitter-4 remote control operates four devices
Transmitter-4PRO-Black remote control operates four automatic devices
Transmitter-4PRO-Black remote control operates four automatic devices
Photocell-N safety photocells consisting of infrared transmitter and receiver
Photocell-N safety photocells consisting of infrared transmitter and receiver

Extra information

  • Correct installation and operation of rolling shutters guarantee their safe and durable service life. To keep shutters in good working condition, follow the instructions listed below:
  • Only qualified personnel trained at DoorHan training centers should install roll-up doors or rolling shutters.
  • Install rolling shutters following DoorHan operation and installation instructions and technical data sheets.
  • Rolling shutters should open smoothly without jolts or jamming.
  • Use only specified equipment for opening and closing of the shutters.
  • Don’t exert pressure exceeding 100 N when opening the roller shutters.
  • Partial opening or closing of the shutters, especially with large curtain area (curtain size more than 3,000 x 2,000 mm), is undesirable.
  • If rolling shutter is equipped with a mechanical lock or a latch lock unlock it before opening the shutters.
  • If rolling shutters are operated with rod crank, hold the crank rod at 45° when turning it. According to EN12453 and 12604 standards one should not exert pressure exceeding 390 N when operating roller shutters. If the operated rolling shutter is large use emergency manual drive only for closing.
  • Follow the corresponding operation and installation instructions when using an electric motor.
  • Do NOT permit children to play on, near the operating area, or with the rolling shutters or to operate controls.
  • Keep door/window opening clear of people and animals while operating the shutters.
  • Never stay or cross an opening under a moving shutter curtain as it may cause serious injury.
  • Don’t strike the shutter curtain or obstruct its movement.
  • Keep the door/window opening clear of any objects while operating the shutters as it may cause their damage.
  • Never install any optional equipment or accessories, replace or adjust some shutter parts without prior consultation with the manufacturer (consultation is considered to be be a communication describing the arisen problem which can be documented).
  • In winter, in case of ice coating of rolling shutter parts, it’s necessary to pre-tap the shutter curtain perimeter to release it of ice before operating the shutters. Pay special attention to the place where bottom part of the curtain touches the floor or window sill (keep it clean too).
  • Carry out rolling shutter maintenance at least once a year.
  • Should the rolling shutters be used for other purposes or should their size exceeds the recommended one, the manufacturer holds no responsibility for their integrity and correct operation.
  • Adjustments or repairs must be made by a trained technician using proper tools and instructions.
Packing in cardboard Packaging features
Contents The packaging comprises bubble wrap and white double wall corrugated cardboard; the hood with rolled in shutter curtain is wrapped in bubble wrap and than in cardboard sheet. This box is than double wrapped in stretch film and fixed with adhesive tape with DoorHan logo.
Width, mm from 165 to 300
Height, mm from 165 to 300
Length, mm from 500 to 6 000
DoorHan warrants the roll-up doors/rolling shutters to operate properly for a period of 2 years from purchase date.
  • Use roll-up doors/rolling shutters made of RH77 or RHE84 profile only for installation in entrance, garage or drive-through openings and in regions with high wind load.

New Products

New steel side caps RSK300, made of zinc-coated steel, ensure high rigidity and corrosion resistance, and are painted the same colour as the shutter hood.
Safe packaging in white double wall corrugated cardboard boxes.

Other customers also looked at

Navigation